查看: 309|回复: 5

[求助] hi3559调试rtl8189es,sdio接口,识别不了设备,求大佬帮忙

[复制链接]
发表于 2019-2-11 11:20:56 | 显示全部楼层 |阅读模式
himci: card connected!
mmc1: mmc_rescan_try_freq: trying to init card at 400000 Hz
mmc1: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 0 timing 0
himci 100d0000.himciv200.SD: Initial signal voltage of 3.3v
mmc1: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc1: starting CMD52 arg 00000c00 flags 00000195
mmc1: req done (CMD52): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD52 arg 80000c08 flags 00000195
mmc1: req done (CMD52): -110: 00000000 00000000 00000000 00000000
mmc1: clock 400000Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
mmc1: clock 0Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
mmc1: gated MCI clock
mmc1: starting CMD0 arg 00000000 flags 000000c0
mmc1: clock 400000Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
mmc1: ungated MCI clock
mmc1: req done (CMD0): 0: 00000000 00000000 00000000 00000000
mmc1: clock 0Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
mmc1: gated MCI clock
mmc1: clock 400000Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
mmc1: ungated MCI clock
mmc1: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc1: clock 0Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc1: gated MCI clock
mmc1: starting CMD8 arg 000001aa flags 000002f5
mmc1: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc1: ungated MCI clock
mmc1: req done (CMD8): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD5 arg 00000000 flags 000002e1
mmc1: req failed (CMD5): -110, retrying...
mmc1: req failed (CMD5): -110, retrying...
mmc1: req failed (CMD5): -110, retrying...
mmc1: req done (CMD5): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc1: starting CMD1 arg 00000000 flags 000000e1
mmc1: req done (CMD1): -110: 00000000 00000000 00000000 00000000
mmc1: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
mmc1: mmc_rescan_try_freq: trying to init card at 300000 Hz
mmc1: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 0 timing 0
himci 100d0000.himciv200.SD: Initial signal voltage of 3.3v
mmc1: clock 300000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc1: starting CMD52 arg 00000c00 flags 00000195
mmc1: req done (CMD52): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD52 arg 80000c08 flags 00000195
mmc1: req done (CMD52): -110: 00000000 00000000 00000000 00000000
mmc1: clock 300000Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
mmc1: starting CMD0 arg 00000000 flags 000000c0
mmc1: req done (CMD0): 0: 00000000 00000000 00000000 00000000
mmc1: clock 300000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc1: starting CMD8 arg 000001aa flags 000002f5
mmc1: req done (CMD8): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD5 arg 00000000 flags 000002e1
mmc1: req failed (CMD5): -110, retrying...
mmc1: req failed (CMD5): -110, retrying...
mmc1: req failed (CMD5): -110, retrying...
mmc1: req done (CMD5): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: clock 300000Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc1: starting CMD1 arg 00000000 flags 000000e1
mmc1: req done (CMD1): -110: 00000000 00000000 00000000 00000000
mmc1: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
mmc1: mmc_rescan_try_freq: trying to init card at 200000 Hz
mmc1: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 0 timing 0
himci 100d0000.himciv200.SD: Initial signal voltage of 3.3v
mmc1: clock 200000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc1: starting CMD52 arg 00000c00 flags 00000195
mmc1: req done (CMD52): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD52 arg 80000c08 flags 00000195
mmc1: req done (CMD52): -110: 00000000 00000000 00000000 00000000
mmc1: clock 200000Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
mmc1: starting CMD0 arg 00000000 flags 000000c0
mmc1: req done (CMD0): 0: 00000000 00000000 00000000 00000000
mmc1: clock 200000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc1: starting CMD8 arg 000001aa flags 000002f5
mmc1: req done (CMD8): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD5 arg 00000000 flags 000002e1
mmc1: req failed (CMD5): -110, retrying...
mmc1: req failed (CMD5): -110, retrying...
mmc1: req failed (CMD5): -110, retrying...
mmc1: req done (CMD5): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: clock 200000Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc1: starting CMD1 arg 00000000 flags 000000e1
mmc1: req done (CMD1): -110: 00000000 00000000 00000000 00000000
mmc1: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
mmc1: mmc_rescan_try_freq: trying to init card at 100000 Hz
mmc1: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 0 timing 0
himci 100d0000.himciv200.SD: Initial signal voltage of 3.3v
mmc1: clock 100000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc1: starting CMD52 arg 00000c00 flags 00000195
mmc1: req done (CMD52): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD52 arg 80000c08 flags 00000195
mmc1: req done (CMD52): -110: 00000000 00000000 00000000 00000000
mmc1: clock 100000Hz busmode 2 powermode 2 cs 1 Vdd 21 width 0 timing 0
mmc1: starting CMD0 arg 00000000 flags 000000c0
mmc1: req done (CMD0): 0: 00000000 00000000 00000000 00000000
mmc1: clock 100000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc1: starting CMD8 arg 000001aa flags 000002f5
mmc1: req done (CMD8): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD5 arg 00000000 flags 000002e1
mmc1: req failed (CMD5): -110, retrying...
mmc1: req failed (CMD5): -110, retrying...
mmc1: req failed (CMD5): -110, retrying...
mmc1: req done (CMD5): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: clock 100000Hz busmode 1 powermode 2 cs 0 Vdd 21 width 0 timing 0
mmc1: starting CMD1 arg 00000000 flags 000000e1
mmc1: req done (CMD1): -110: 00000000 00000000 00000000 00000000
mmc1: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
发表于 2019-2-11 12:26:18 | 显示全部楼层
把内核驱动里面的sdio电压切换去掉试试
 楼主| 发表于 2019-2-11 13:23:10 | 显示全部楼层
yangcanx 发表于 2019-2-11 12:26
把内核驱动里面的sdio电压切换去掉试试

麻烦能说具体点嘛,是修改menuconfig?
发表于 2019-2-11 15:58:54 | 显示全部楼层
drivers/mmc/core/sdio.c里面mmc_set_signal_voltage这个函数屏蔽掉
 楼主| 发表于 2019-2-11 16:38:18 | 显示全部楼层
yangcanx 发表于 2019-2-11 15:58
drivers/mmc/core/sdio.c里面mmc_set_signal_voltage这个函数屏蔽掉

不行的,看问题是wifi那边没回应。
发表于 2019-4-23 22:33:52 | 显示全部楼层
楼主解决了吗?怎么解决的,我也遇到同样的问题
您需要登录后才可以回帖 登录 | 注册

本版积分规则

© 2008-2017 当前位置 易百纳技术社区论坛 返回 易百纳技术社区 ( 苏ICP备14036084 )   Powered by Discuz! X3.1
快速回复 返回顶部 返回列表